Tool Cabinet – Carcase Redo

Tool Cabinet Carcase 

So this is a continuation of the tool cabinet projet where at my first attempt, I did not pay attention enough to the carcase glue-up that I judged that it was too out of square that I devised to redo the whole case and start again

It is now all glued up and square and happy with it.  

Other Components 

The plane till was pretty much already done and constructed so I was able to fit the components into the new case.  Just not finalized the install of the components yet into the case.  

The Doors 

The Tool Cabinet has 2 exterior doors which I started to cut the different components.  The frame of one of the door is dried assembled but not glued up yet.  This is the inside frame of the door that is assembled.  I still need to fit the parts for the outside of the door and eventually assemble it with the inside frame of each door and fit with each of the doors.  

All the parts are accounted for, but some fitting and joinery needs to be done to have some nice doors and to eventually hang them and hang some tools inside them.  

 

Once again, take your time.  Although I want this cabinet to be done or advance a bit faster then it is right now (current cabinet is a mess), it is worth while.  I consider that shop furniture are great practice pieces and are not exposed to “customer” and it is normally for you.  

I still want shop furniture to look good though.  In my opinion, it does not mean trash but a good way to practice either a new technique or joint.  It might not be perfect, but it is good practice. 

Tool cabinet components

Tool cabinet components

Tool Cabinet – Structure

The tool cabinet structure is now finally built and glued up.  All 4 corners and the shelf that serves as the support for the plane till is all up and assembled.  Like many assemblies, some fun always arise close to the end and this is why dry assemblies are always necessary to find issues before applying the glue.

Shelf

The structure has a shelf at about 1/3 from the bottom of the cabinet that also serves to support the plane till.  The joint are through tenons and was pretty easy to fit and drive within the sides.

Square through tenons that will hold a shelf for the tool cabinet

Once the mortises were cut, I was able to derive the tenons through the shelf.  Yes yes normally, you would do the other way around.  It did not happen this way for this assembly and it still worked.

For the mortises, they are a little shallower then the thickness of the shelf by a total of 1/8″.  I chose to trim the tenons with a rabbeting block place with an edge guide and made sure that both side received an equal amount of shaving not to take too much from one side of the tenons.  Same amount of shavings were taken on both sides of the shelf so that side to side so that when the case would be assembled, the shelf would be level from side to side.

Piece of Walnut used as a edge stop for a rabbeting plane to trim the tenons

Piece of Walnut used as a edge stop for a rabbeting plane to trim the tenons

Assembly

After a first dry fit, I found out that the shelf was too long in between the tenons edge and made the side bow and the dovetails would not close together.  So back to measure the side and indeed, a 1/4″ was too much. So no wonder that the case would not come together.

Back to the bench and was able to trim  the extra material and on to another dry fit and this time was perfect.

So came time to glue up and took my time and worked with the PVA open time so the dry fitting got my clamps all ready to the glue up time.  Applied the glue and measured the different dimensions and all was good.  Left it to glue for all night and here it is….

Tool Cabinet on edge

Tool Cabinet on edge

Tool Cabinet on edge

Tool Cabinet on edge

Tool Cabinet on edge

Now on to the other components where the dimensions can be derived from the tool cabinet structure itself.  The dimensions that are stated in the plan are pretty good reference and some parts were cut to rough lengths. Knowingly that they were to be adjusted once the structure was all assembled.

Tool Cabinet – Carcase Assembly

Carcase Assembly

The past week was concentrated on completing the carcase assembly frame and have the joinery completed and fitted.  It is a cabinet carcase with dovetail at the 4 corners. Last post covered the dovetail cutting process all done by hand and now was time to fit all 4 corners of the main assembly.

Tool Cabinet Carcase dry fitted

Tool Cabinet Carcase dry fitted

Tool Cabinet Carcase

Tool Cabinet Carcase

It has been a while that I cut dovetails and it really showed and fitting them was a pretty experience.  A bit too much gaps to show but  still tight enough for the structural side of things.  It holds pretty as we speak and it is only dry fitted.

I checked for square in all 4 corners and all was good.  Just one corner that I saw some small amount of light, maybe 1/64 to 1/32 which to me, is not worth playing with, fearing to change something and make it worst.  Will adjust the dimensions of the other components if required.

Shelf

Towards the lower end, there is a shelf that is through tennonned in the carcase assembly which will stiffen the whole assembly.  Although the main wood is cherry, I did not have wide enough boards to cover the shelf in one piece but had a maple board from another project that was a left over and for the most part, was large enough

For the most part, it was a clean board except for one corner that had a broken/damaged edge.  I decided to go ahead with the board as one edge was going to be going towards the back of the cabinet which will be hidden once all assembled.

tool cabinet shelf

tool cabinet shelf

I may need to adjust the placement of the tenons on that edge based on the plans but that should not be an issue.  It’s length was derived based on relative dimensioning of the carcase assembly that is now dry fitted

Next Steps

Next steps is to fit the shelf and the joinery with the through tenons in the carcase. Will then be able to glue up the carcase and start working on the external doors for the dimensions.

Will also be ordering the hinges for the external doors so that when they are completed, I will at least be able to hang them.  I may not be ordering all the hinges that the plan calls for as I have not finalized the tool placement inside the cabinet.  Some internal hinges I might forgo altogether as I might not be going with the storage options as is. Part of the customization of the storage based on the tools that I have.